• Create BookmarkCreate Bookmark
  • Create Note or TagCreate Note or Tag
  • PrintPrint
Share this Page URL
Help

Chapter 4. Sound Annoyances > CONFIGURATION ANNOYANCES

CONFIGURATION ANNOYANCES

FIGURING OUT YOUR SOUND CARD

The Annoyance:

I want top-notch sound for my new game. How do I find out what sound card my system currently uses before I splurge on a new one?

The Fix:

First, determine whether you use an integrated sound chip or a PCI sound card. Take a look behind the PC and trace the speaker cable to the output jack. If the cable connects to a jack in the rear I/O area of the PC (the cluster of serial, parallel, USB, Ethernet, and other ports commonly found below the power supply), you're using an integrated sound chip on the motherboard.

Now let's get the skinny on your specific sound hardware using the DirectX diagnostic (dxdiag.exe). Select Start → Run, enter dxdiag in the Run box, and click the OK button. When the dialog box appears, click the Sound tab for a complete breakdown of the sound device and its driver info (see Figure 4-1). Don't let a PCI designation throw you-even a motherboard chip can use a PCI architecture within the system (it's not limited to a card in a slot).

Figure 4-1. Use dxdiag.exe to identify your current sound hardware and driver information.


If you decide to add a sound card, it should automatically disable any onboard (motherboard) sound device. However, this does not always happen perfectly. After you install a new sound card, check the System Setup and verify that the integrated sound device is disabled (see the "AC97 Audio" entry in Figure 4-2). If not, disable the sound device and save your changes. Remember to reconnect your speaker cable (along with microphones and line input cables) to the new sound card.

Figure 4-2. When you install a PCI sound card, make sure any onboard sound device is disabled.


AUDIO PORT CONFUSION

The Annoyance:

I plugged my PC speakers into the jack with the little music note above it, but I don't hear any sound.

The Fix:

Wrong jack, Jack. The little musical note sometimes denotes the Line In connection. The Speaker Out (or Line Out) connection is typically greenish-yellow, and often uses a symbol such as "((o))–>" (reminiscent of sound waves with an arrow going outward). The opposite (Line In) jack is often blue, and marked with a reverse symbol, such as "((o))<–" (the same sound waves with an arrow going inward). Recheck your speaker connections and try the speakers in another jack.

Cables and Static

If you hear speaker static-especially when moving your speakers-check your connections at the sound card, and reseat the speaker jack if necessary. If you encounter static when moving the sound cable, you may need to replace the speaker set with a better-quality model.


GETTING THE MOST FROM POSITIONAL SOUND

The Annoyance:

What is A3D-I sound and how do I enable it on my sound device?

The Fix:

Ah, this is 3D sound. Aureal 3-Dimensional (A3D) sound technology is based on human hearing. In everyday life, you can tell the direction of a sound (front, side, or back) because of slight delays and volume shifts in the sound when it strikes your ears. A3D technology attempts to duplicate these effects through a sound card and only two speakers (rather than the five or more speakers often used with surround-sound systems), by using "positional sound." Positional sound uses slight differences in sound timing and volume to "trick" the listener into hearing sound relative to their location. For example, a listener can hear gunfire off to the left, footsteps creeping up from behind, or any number of interactive sound effects.

A3D relies upon a compliant sound device (and drivers), a set of stereo speakers, and a game or other application that can produce 3D sound effects. The specs of your sound system will typically tell you if 3D sound is available. For your game, simply check the Sound tab or sub-menu of the game's configuration menu. (Refer to the game manual for details.)


Tip:

To create positional sound, place a speaker on each side of your monitor at a 30–45 degree outward angle.


ENABLING THE STANDARD JOYSTICK

The Annoyance:

My joystick fails to work when I connect it to the sound card's 15-pin port.

The Fix:

Start with the basics and check the joystick's connection to its 15-pin port. Also, check with the sound card maker and make sure that the 15-pin port is actually a joystick port (as opposed to some other proprietary feature). You may also need to set the small jumper located on the sound card to joystick mode, rather than MIDI mode.

Next, open the System control panel, click the Hardware tab, and then click the Device Manager button. Expand the "Sound, video, and game controllers" entry, and look for an entry such as Standard Game Port (see Figure 4-3). If the entry is missing, download and install the latest drivers for your sound card. A yellow exclamation or question mark next to the entry indicates a hardware conflict. Power down the computer and remove any other game port devices in the system (look for expansion devices with similar 15- pin ports).

Figure 4-3. Check the Device Manager to ensure that a Standard Game Port is available for the joystick.


If the game port is present with no errors reported, make sure you configured the game to use the joystick. Remember that games often let you select between keyboard, mouse, and joystick input devices. If the problem continues, try another joystick.

ENJOYING SURROUND SOUND

The Annoyance:

I've got my speakers connected, but how do I get surround sound to work when playing a DVD movie?

The Fix:

You need to configure both Windows XP and your DVD player for 5.1 (6-speaker) sound. To adjust the speaker configuration under Windows, open the Sounds and Audio Devices control panel, click the Advanced button under "Speaker settings," and then select "5.1 surround sound speakers" from the "Speaker setup" drop-down menu (see Figure 4-4). Click the Apply button to save your changes.

Figure 4-4. Configure Windows XP for 6-speaker operation.


Now start a DVD player application, such as WinDVD or Windows Media Player (WMP), and configure the audio for 6-channel (5.1) sound. To do this within WMP, click Tools → Options, click the DVD tab, and then click the Advanced button. Under Audio Interface, select "using 6-speakers" and click the Apply button (see Figure 4-5). Your surround sound should work fine-enjoy the show!

Figure 4-5. Configure the DVD movie player for 6-speaker operation.


RATTLE AND HUM

Whether in a sound card or in a speaker set, amplifier circuits produce some amount of hum. Since audio signals are amplified at several stages before they reach your ears, excess amplification can bring undesirable noise (like hum) to the forefront and ruin your audio experience. As a rule, increase volume early in the sound process (such as the Windows Volume Control), and keep the speaker volume as low as possible. If you adopt the reverse tactic (keep the Volume Control settings low and force the speakers to amplify things), you'll hear a lot of noise in the signal.


GETTING EAX TO WORK

The Annoyance:

How come I can't get my EAX feature to work?

The Fix:

Environmental Audio Effects (EAX) bring a wide range of sound effects to a computer's sound playback, including reverb, 3D surround sound, time scaling (to speed up or slow down playback), and so on. EAX can also simulate audio environments, such as theaters or bedrooms, and perform other tasks on sound files. Unfortunately, only certain sound devices support EAX.

With EAX 4.0 drivers now available, make sure you use the most recent sound device drivers from your sound card manufacturer, as well as the latest version of DirectX from Microsoft (http://www.microsoft.com/directx). If EAX features work under all but one game, check the game itself (rather than the sound card's EAX support) for problems. Make sure you enable EAX within the game's sound options menu (see Figure 4-6). Also, check for game patches or updates that will enable EAX support within the troublesome game. If no EAX support is available in the game software, you will not be able to access EAX features when you play the game.

Figure 4-6. Be sure that EAX support is enabled within the game itself.


DEVICE DISAPPEARS AFTER BIOS UPGRADE

The Annoyance:

My audio device disappeared after I updated the system BIOS. How do I get it back?

The Fix:

BIOS updates have a nasty habit of resetting onboard options to default settings. If you use onboard audio, the BIOS update may have disabled the audio. Windows will no longer see the onboard audio device. Once you complete a BIOS upgrade, make sure you "Load BIOS Defaults" and reboot the system. If the problem continues, reboot to the System Setup and open the Integrated Peripherals menu. Locate the onboard audio device (often labeled something like "AC'97 Audio") and make sure the device is enabled.

If the problem continues to haunt you, download and reinstall the latest motherboard drivers (including the sound drivers) to restore the sound system. However, some motherboard driver updates may call for a complete reinstallation of Windows. If you must reinstall Windows, do it before you install the new motherboard drivers. Finally, restore your other device drivers, applications, and datafiles from backups or original media.


Tip:

Always perform a complete backup of the system before you attempt a BIOS upgrade or reinstall Windows from scratch.


MULTIMEDIA PLAYER ASKS FOR A CODEC

The Annoyance:

When I try to play a sound file, the player stops and asks for a codec. What the %#$@ is a codec and how do I get the right one(s) for my system?

The Fix:

Codecs compress and decompress multimedia data and provide the instructions needed for multimedia players (e.g., InterVideo WinDVD 6 or Windows Media Player) to handle a specific file type, such as MPG, MP3, QuickTime, and so on.

Today, common codecs are installed along with the operating system, and additional codecs are installed with their corresponding applications. For example, if you install a music player, you'll likely get MP3 codecs. To inspect your available codecs, open the System control panel, click the Hardware tab, click the Device Manager button, and expand the "Sound, video, and game controllers" entry. Right-click the Audio Codecs entry and choose Properties to see the installed codecs (see Figure 3-3 in Chapter 3).

If a codec goes missing, chances are that the application or its codecs have been damaged or corrupted (or the application was never installed properly in the first place). Uninstall the application and then reinstall it again from scratch. If the trouble persists, check your audio or video codecs for duplicate entries. Duplicates can sometimes occur when you repeatedly install similar programs or hardware devices, and conflicts between duplicate entries can stop that codec from being used. Right-click any duplicate codecs and choose Remove.

HEADPHONES DISABLE INTERNAL SPEAKERS

The Annoyance:

I disconnected a pair of headphones from my laptop, and now the internal speakers don't work.

THE COMPLETE CODEC

Normally, codecs are installed with media player software (e.g., RealPlayer or QuickTime). However, software engineers occasionally update codecs to keep pace with bug fixes and compression improvements. Check your player for automatic codec updates from the Internet. To do this in Windows Media Player, click Tools → Options and click the Player tab. In the "Automatic updates" section, make sure you check the "Download codecs automatically" box.


The Fix:

Although this problem may seem like a hardware malfunction, it's really a driver issue. For example, the audio driver recognizes the headphones and disables the internal speakers, but does not re-enable the internal speakers once you disconnect the headphones. Reboot the laptop with the headphones disconnected to restore the internal speakers normally. Also, contact your laptop maker and install the most recent audio drivers.

  • Creative Edge
  • Create BookmarkCreate Bookmark
  • Create Note or TagCreate Note or Tag
  • PrintPrint